Domestic Shipping to USA, Australia and Canada!

Output TX

Stereo buffer + summing box

Two amps, zero buzz.

$199.00 USD

Output TX sits at the end of your signal chain. Sum stereo to mono, split to two amps, and kill noisy ground loops with a transformer-isolated output.

  • Free US, CA & AU shipping over $149
  • 2 year warranty
  • 30 day money back
  • Stereo to mono summing
  • Gets rid of noisy ground loops
  • Fixes out of phase amps
  • Stereo buffer

Is this for you?

Yes if you've got a stereo board that sometimes goes into one amp and sometimes two, or you run two amps and fight noisy ground loops.

No if you need XLR to the sound desk. That's LongLine. Just want two amps without the hum and don't need buffers or summing? Buzzkill is passive and costs less.

Not sure? Email info@goodwoodaudio.com with your rig and we'll help you decide.

What players say

If you're running a dual amp or stereo setup, the Output TX is a must-have. Pristine signal, zero noise or buzz, simple design, and a solid build. I like it so much I got two, one for each pedalboard!
Mark Lettieri ★★★★★ Customer review
It has turned out to be the perfect solution to sum my stereo rig down to mono for smaller shows where a 2 amp rig is not feasible.
David Weaver ★★★★★ Google review
Exactly what I needed, and couldn't find anything else with the right set of features and the nice compact size.
Louis Schwartz ★★★★★ Google review
The Output TX is a fantastic solution to stereo rigs and mono sum scenarios.
Gabriel Adams ★★★★★ Google review
Output TX at the end of the signal chain on a large pedalboard

Three modes

Stereo Sum, Split Sum and Mix mode, set with the internal DIP switches. One box covers stereo and mono stages.

Output TX button side with ground lift and phase

Noisy ground loops gone

The audio transformer on the right output isolates the second amp, so there are no more noisy ground loops. Flip the polarity too, so your amps aren't cancelling out frequencies.

Output TX mounted under an angled pedalboard, showing the TX, 180 and Sum push buttons

Stereo buffer

Both outputs are buffered, so long cables to your amps don't cut your top end.

How to connect

Output TX in a stereo rig into two amps

Your stereo board into two amps, with both outputs buffered.

ModesStereo Sum, Split Sum, Mix (internal DIP switches)
IsolationAudio transformer on the right output, with ground lift
PhaseInverts the right output
ImpedanceInput 1MΩ, output very low
Power9V DC, centre negative, 50mA
Dimensions66 x 111 x 31 mm (2.6 x 4.37 x 1.22 in)
Warranty2 years
Price$199.00 USD
Specs: audio performanceTHD, noise, frequency response and more
SpecOutputs
Total harmonic distortion (THD)What does this mean?Under 0.0011%

How much the box colours your sound by adding harmonics of its own. Lower is cleaner. Numbers this small are far below anything you can hear.

Signal to noise ratioWhat does this mean?Over 104 dB

The gap between your guitar signal and the box's own hiss. Bigger is better. 100 dB means the hiss is 100,000 times quieter than your signal.

Noise floorWhat does this mean?Below -107 dBV

The hiss the box makes on its own with nothing playing. The more negative the number, the quieter it is.

Measured on our test bench at 1Vrms, 1kHz unless noted. Worst channel shown.

FAQ

Where does it go?
At the end of your pedalboard, after your last pedal, feeding your amp or amps.
What's the difference between Stereo Sum, Split Sum and Mix mode?
Stereo Sum (how it ships) merges your left and right inputs, without raising the volume, and sends that to both outputs. Great for delays and reverbs. Split Sum (DIP switch): with the Sum button out, left goes to left and right to right as normal. Push it in and the right input is muted, and the left input goes to both outputs. Great for dual mono rigs, or for summing stereo modulation. Mix mode (DIP switch) mixes two lines, like a fully wet delay with a parallel reverb and dry through, or two separate instruments or sources.
Will it fix noisy ground loops with my two amps?
Yes. That's the transformer's job. Press the black ground lift button and your left and right outputs are galvanically isolated from each other, so the ground loop disappears.
Output TX or LongLine?
Need XLR to the desk or long cable runs? LongLine. Playing through amps on stage? Output TX.
Output TX or Buzzkill?
Buzzkill is passive and only gets rid of noisy ground loops and polarity issues. Output TX adds buffers and stereo summing.

Reviews

Output TX$199.00 USD
Just added to your wishlist:
My Wishlist
You've just added this product to the cart:
Go to cart page