$174.00
Are you ready to dip your feet into the deep pool of Wet Dry Wet? Isolator is the gateway with which you enter.  Custom Pedals like this one are built to order...
Availability: Many In Stock

Are you ready to dip your feet into the deep pool of Wet Dry Wet? Isolator is the gateway with which you enter. 

Custom Pedals like this one are built to order and therefore come with a lead time after purchase.  Currently the wait time for this junction is an estimated 4 weeks before it is ready to ship. 

Isolators Purpose 

We get asked all the time how to start experimenting with a Wet Dry or Wet Dry Wet style rig.  To fully commit takes a lot of patience, time and honestly, some hardware.  If you aren't sure this is the way you want to do, experiment with as little as possible first! Add Isolator and instantly get a mute-able, isolated dry output to add to your series pedalboard! 


Optional Add-Ons

 

Ground Lift and Phase Control: You can add an isolation transformer to the Dry (B.out) Output to correct against ground loops and phase issues between amps.  


If this is something you find confusing (do I need it or don't I), a good way to look at this is if you want to use 2 amps at a gig, get one transformer.  If you're happy to drop to one amp if you get a ground loop / phase issue at a gig, don't get any transformers.  If you're happy to drop to two amps at a gig if you get a ground loop / phase issue, get one transformer.  

You need one less transformer than the amount of amps you want to use while playing. 

This doesn't necessarily apply to amp simulators as they typically send to a DI which has ground lift built in (double check your DI to make sure). Therefore you wouldn't necessarily need a transformer in this box as well as the DI transformer.


Manual & Specs

Isolator at its core is a buffered split with a few extras added in for good measure.  The main goal here is to take your dry effects (overdrives, fuzz, distortion etc) and send them to your modulation / wet effects (as normal) AND to a dedicated dry amp.  

This allows for your core tone (your dry effects) to be heard clearly without being muddied up by delays, reverbs and other glorious noise makers that we as guitarists tend to overuse. 

Instantly mute your dry amp with Isolator using your midi controllers amp switching jacks, an RMT or any other normally open momentary footswitch you have laying around! 

Input

Plug your last dry effect in here. Your signal will now be split to two places: 
Out A - Send this to your first wet effects 
Out B - Send this to your dry amp.  This is the output that is both mute-able and isolated with ground lift and phase pushbuttons. 

Outputs

There are two outputs on Isolator: 
1. A Output - This is the output you use to send signal to your first wet effect.  This output is not affected by the dry mute. 
2. B Output - This is the output that you use to send signal to your dry amp.  This output can be muted and is connected to the ground lift and phase pushbuttons (it is an isolated output). 

RMT Jack

The RMT jack on Isolator can be used to mute the dry output remotely.  You can connect a TRS cable and a Goodwood Audio RMT pedal to control this dry mute or connect your midi controllers amp switching jack.  

If you decide to use your midi controllers amp switching jacks, or a standard momentary switch, you can use a TS / mono patch cable.  No need for TRS. 

Pushbuttons 

There are three pushbuttons on Isolator: 
a. TX (if transformer added) - Use this to lift the ground on the B output.  This is only needed if you hear a hum in your multi-amp setup.  If you have a ground loop between amps, this button should get rid of it. 
b. 180 (if transformer added) - Use this if your two amps are out of phase with each other.  If out of phase, they will most likely sound 'honky' and have a reduced bottom end.  If you unplug one amp and the bottom end returns / honk is gone, you are most likely out of phase.  Push this button to correct that. 
c. Mute B - If not using the RMT jack, use this pushbutton to mute the B output. 
Note: If the RMT jack is plugged in and being used, the RMT will override the pushbutton state. 

These are designed to last and come with a 2 year warranty! 

All Isolators are made with high quality, durable components.

IMPORTANT - Use only 9vDC centre negative plug to power! 

Current Draw/Power: 75mA, Center Neg 2.1mm

Isolator Box Dimensions: 113mm x 60mm x 31mm

Input Impedance: 1Meg
Output Impedances: 500ohms

 

We know the best part about buying a new product is receiving that freshly wrapped package in the mail. The worst part however, is the agonising wait of what seems like decades for it to arrive.  We will always do our best to get your newly purchased product to you in a timely manner.

Domestic

All orders are sent via USPS and generally arrives within 1-5 days. 

If you don't receive a tracking number from us after purchase, first check your junk folder, then send us an e-mail and we will find it for you! 

International

We use USPS and UPS for International shipping.  Since Covid hit, international shipping has been very hard to predict with any certainty.  Please be patient and don't be alarmed if your order takes a bit longer than normal! 

Unfortunately we have no control on how long the package will take to arrive once it has shipped.  If your package does not arrive within the time mentioned above, simply send us an email, SMS, letter via carrier pigeon or come tell us in person and we will do our best to look into it from our end.